« previous next »
Pages: 1 [2]   Go Down

Author Topic: Aftermarket magazines  (Read 954 times)

0 Members and 1 Guest are viewing this topic.

PAX

  • SKS Guru
  • **
  • Posts: 4996
  • ALL IS NOT QUIET ON THE WESTERN FRONT
Re: Aftermarket magazines
« Reply #15 on: March 30, 2025, 12:39:41 AM »
Quote from: Sksnewb56 on March 28, 2025, 08:48:50 PM
Not to bad, they?re 10$ each.  He only takes a minimum order of 10 units.  They do stack nicely in ammo cans before heading for the range



You wanna sell one or two of yours or trade a few good strippers for a couple? PAX
Logged
"A free people ought not only be armed and disciplined", George Washington,
"but they should have sufficient arms and ammunition to maintain a status of Independence from any who might attempt to abuse them." Sent from behind the KaliKurtain. PAX

Sksnewb56

  • SKS Newbie
  • Posts: 28
Re: Aftermarket magazines
« Reply #16 on: March 30, 2025, 01:08:54 PM »
I?d like to keep the ones I have atm, and I?ve got some stripper clips.  No need for stripper clips when I have these 3d printed unit either.  I?m hoping he is able to print some that will hold 10rnd rather then the 5rnds like it is now

Also if you wanted he may ship to the states if you covered shipping, as he?s located in Ontario Canada near me, plus with your dollar rate could be cheap for you to do a order of ten for yourself too
Logged

PAX

  • SKS Guru
  • **
  • Posts: 4996
  • ALL IS NOT QUIET ON THE WESTERN FRONT
Re: Aftermarket magazines
« Reply #17 on: March 30, 2025, 03:57:17 PM »
I'd only order a couple to replace my home-made fives specifically for my fixed flush 5 rifle. They look neat and cool and should carry nicely in the field.
I have a few 40mm ammo boxes of Chinese chest rigs with M67 on strippers, some web/Molle belts/harnesses with Chinese/Russian vertical & Yugo horizontal leather pouches combined with hydration, and at least a dozen of both loose with Chinese AP on strippers. I'm only missing tracers. PAX
Logged
"A free people ought not only be armed and disciplined", George Washington,
"but they should have sufficient arms and ammunition to maintain a status of Independence from any who might attempt to abuse them." Sent from behind the KaliKurtain. PAX

Sksnewb56

  • SKS Newbie
  • Posts: 28
Re: Aftermarket magazines
« Reply #18 on: March 30, 2025, 04:56:21 PM »
Maybe you?ve got a few friends you could order with to split up the ten ?? I would think would fit nicely in magazine pouches or Molle packs too.  They?re only 2.5? wide 5/8? thick and just shy of 3? tall
Logged

PAX

  • SKS Guru
  • **
  • Posts: 4996
  • ALL IS NOT QUIET ON THE WESTERN FRONT
Re: Aftermarket magazines
« Reply #19 on: March 31, 2025, 01:20:27 AM »
Quote from: Sksnewb56 on March 30, 2025, 04:56:21 PM
Maybe you?ve got a few friends you could order with to split up the ten ?? I would think would fit nicely in magazine pouches or Molle packs too.  They?re only 2.5? wide 5/8? thick and just shy of 3? tall

Nobody but me has use for 5 rounders. Those just make a neat package for my Canadian Deer Slayer build. Prolly fit in a slip-on butt pouch perfect. PAX
Logged
"A free people ought not only be armed and disciplined", George Washington,
"but they should have sufficient arms and ammunition to maintain a status of Independence from any who might attempt to abuse them." Sent from behind the KaliKurtain. PAX

cvasqu03

  • Board Supporter
  • SKS Guru
  • *****
  • Posts: 6341
Re: Aftermarket magazines
« Reply #20 on: March 31, 2025, 01:39:09 AM »
Quote from: Sksnewb56 on March 28, 2025, 08:48:50 PM
Not to bad, they?re 10$ each.  He only takes a minimum order of 10 units.  They do stack nicely in ammo cans before heading for the range



That's pretty nifty.  To my knowledge, nobody has tried to modernize the stripper clip 'till now. 
Logged
I am the one they call Cesar.

Sksnewb56

  • SKS Newbie
  • Posts: 28
Re: Aftermarket magazines
« Reply #21 on: March 31, 2025, 04:42:47 PM »
Quote from: PAX on March 31, 2025, 01:20:27 AM
Quote from: Sksnewb56 on March 30, 2025, 04:56:21 PM
Maybe you?ve got a few friends you could order with to split up the ten ?? I would think would fit nicely in magazine pouches or Molle packs too.  They?re only 2.5? wide 5/8? thick and just shy of 3? tall

Nobody but me has use for 5 rounders. Those just make a neat package for my Canadian Deer Slayer build. Prolly fit in a slip-on butt pouch perfect. PAX

Well this gentleman that makes them he is located in Ontario Canada if that helps ? lol
Logged

JimmyJamesKY

  • Board Supporter
  • SKS Guru
  • *****
  • Posts: 3870
  • I wish I didn't know now what I didn't know then..
Re: Aftermarket magazines
« Reply #22 on: March 31, 2025, 05:06:25 PM »
I have to say those are super cool.  8)

Is that a website for 3D printer schematics?  It doesn't look like a rifle related sight, but I just clicked the link and took a peek.  I didn't browse. 

I could see buying a set if they were 10 rounders.  Wonder what the tariff is on stripper devices.  (get your mind out of the gutter) :downtown:
Logged
Good friends will lend a hand, great friends will grab a leg....

Sksnewb56

  • SKS Newbie
  • Posts: 28
Re: Aftermarket magazines
« Reply #23 on: March 31, 2025, 05:15:41 PM »
Quote from: JimmyJamesKY on March 31, 2025, 05:06:25 PM
I have to say those are super cool.  8)

Is that a website for 3D printer schematics?  It doesn't look like a rifle related sight, but I just clicked the link and took a peek.  I didn't browse. 

I could see buying a set if they were 10 rounders.  Wonder what the tariff is on stripper devices.  (get your mind out of the gutter) :downtown:

Link I provided was a clip that shows how easy they load and work, I?m not sure where the details would be for this unit unless he custom made them I?m not sure.

🤔 tariffs on strippers?. I?ll bet it depends what they look like ?. Hahahahaha
Logged
Pages: 1 [2]   Go Up
« previous next »