« previous next »
Pages: 1 ... 40 41 [42]   Go Down

Author Topic: My mods on SKS rifles.  (Read 23133 times)

1 Member and 1 Guest are viewing this topic.

PAX

  • SKS Guru
  • **
  • Posts: 4914
  • ALL IS NOT QUIET ON THE WESTERN FRONT
Re: My mods on SKS rifles.
« Reply #615 on: November 26, 2024, 01:32:31 PM »
Good thinkin on the Yugo lug for bayo retention, PAX
Logged
"A free people ought not only be armed and disciplined", George Washington,
"but they should have sufficient arms and ammunition to maintain a status of Independence from any who might attempt to abuse them." Sent from behind the KaliKurtain. PAX

monaderio

  • SKS Sniper
  • *****
  • Posts: 575
Re: My mods on SKS rifles.
« Reply #616 on: November 26, 2024, 01:44:32 PM »
Here is the muzzle brake that fits FSB. https://www.ebay.com/itm/224071994414
The exit hole diameter is 22mm. The front of the FSB is 21.5mm.
Logged

monaderio

  • SKS Sniper
  • *****
  • Posts: 575
Re: My mods on SKS rifles.
« Reply #617 on: November 28, 2024, 04:30:38 PM »
The first attempt at the shooting range was unsuccessful, likely because the gas block was not being installed correctly, resulting in reduced gas flow. After taking 20 manual single shots, a shell became stuck inside the chamber, so I will have some extra work to do. The new setup has been made with one of my spare Yugo rifles.
Also, I removed the Yugo short barrel and adjusted the gas block along with the chamber honing but I'm not sure if I will put it back because the Russian barrel is in excellent condition and will fit perfectly with some tricks.

« Last Edit: November 29, 2024, 12:19:47 AM by monaderio »
Logged

monaderio

  • SKS Sniper
  • *****
  • Posts: 575
Re: My mods on SKS rifles.
« Reply #618 on: November 28, 2024, 04:54:41 PM »
The barrel with the pitted bore and the frozen gas valve in the grenade launcher position  :) will be replaced on my second receiver and stored until the new project begins.



Logged

monaderio

  • SKS Sniper
  • *****
  • Posts: 575
Re: My mods on SKS rifles.
« Reply #619 on: November 29, 2024, 07:47:31 PM »
I replaced the defective Yugo barrel with a good Russian one. The project involving the Yugo receiver and the Russian barrel setup is complete.
Logged

monaderio

  • SKS Sniper
  • *****
  • Posts: 575
Re: My mods on SKS rifles.
« Reply #620 on: November 29, 2024, 07:54:17 PM »
The thread size of the SKS Grenade Spigot is M14x1 RH.
Logged

monaderio

  • SKS Sniper
  • *****
  • Posts: 575
Re: My mods on SKS rifles.
« Reply #621 on: Yesterday at 12:54:18 AM »
Today, the Yugo-Russian SKS received more modifications. The FSB was pinned, and the barrel was threaded with M14x1 LH. The rifle now has two options: a bayonet or a muzzle brake.


Logged

monaderio

  • SKS Sniper
  • *****
  • Posts: 575
Re: My mods on SKS rifles.
« Reply #622 on: Yesterday at 06:29:11 PM »
Tomorrow, another attempt will be made at the shooting range. The two SKS rifles, one an underfolder with a Yugo action and the other Yugo-Russian will be tested.
The new project " Colapsible, sliding, retractable stock" has began.




Logged
Pages: 1 ... 40 41 [42]   Go Up
« previous next »