Author Topic: Bullpup  (Read 3719 times)

0 Members and 1 Guest are viewing this topic.

jdw006

  • SKS Expert
  • ****
  • Posts: 427
  • MARK IT ZERO
Bullpup
« on: July 26, 2010, 05:40:16 PM »
I ordered one of those Shernic Bullpup stocks.  I was wondering if there is anything you can do to reduce trigger pull/weight (if and when I received this :roll: --that's another story).  Thanks!
I can has a cheezburger?

Kivaari

  • Moderator
  • SKS Sniper
  • *****
  • Posts: 526
    • Kivaari's Little Armory
Re: Bullpup
« Reply #1 on: July 27, 2010, 04:23:07 PM »
I can improve the fit , function, and pull weight of an sks trigger system.

As far as the bullpup trigger connector system, I can't help you with that...whatever it is....

kivaari
quality and correctly engaging SKS trigger tune

SKS....the militia's rifle!

www.kivaari.com

NRA Life Member
Texas State Rifle Association member

FrayAdjacent

  • SKS Shooter
  • **
  • Posts: 77
Re: Bullpup
« Reply #2 on: August 17, 2010, 04:32:03 PM »
It would be my understanding that a trigger job on a regular SKS would carry it's relative improvement over to the SGWorks bullpup kit. 

In fact, since it appears there is some mechanical advantage engineered into the SGWorks bullpup trigger, it should result in a great improvement when combined with Kivaari's trigger work.   I have a stock on order, but it will be a while.  I am thinking about sending off the trigger group to have it sweetened up beforehand... but I might want to wait until I get the stock, so I can do a before and after comparison. 

Kivaari

  • Moderator
  • SKS Sniper
  • *****
  • Posts: 526
    • Kivaari's Little Armory
Re: Bullpup
« Reply #3 on: August 18, 2010, 04:58:38 PM »
Quote
it appears there is some mechanical advantage engineered into the SGWorks bullpup trigger

How so?

kivaari
quality and correctly engaging SKS trigger tune

SKS....the militia's rifle!

www.kivaari.com

NRA Life Member
Texas State Rifle Association member

KOOLmike

  • MEMBER IS BANNED
  • SKS Guru
  • **
  • Posts: 7905
  • MEMBER IS BANNED
Re: Bullpup
« Reply #4 on: August 18, 2010, 06:52:25 PM »
Quote
it appears there is some mechanical advantage engineered into the SGWorks bullpup trigger

How so?



Is it possible the mechanism creates additional leverage thus reducing felt pull?

Whether there is a mechanical advantage or not, a trigger job would certainly have an affect on the felt pull of the bullpup. With a simple mechanical connection, the force required to actuate the bullpup trigger would depend on the force required to actuate the original TG, and the felt pull would be realized accordingly. Right? Right? :mrgreen:
MEMBER IS BANNED

richtherake

  • Board Supporter
  • SKS Gunsmith
  • *****
  • Posts: 1501
  • That's my Rottweiler May Day. She's a fat load.
Re: Bullpup
« Reply #5 on: August 19, 2010, 11:16:34 AM »
a trigger job would certainly have an affect on the felt pull of the bullpup. With a simple mechanical connection, the force required to actuate the bullpup trigger would depend on the force required to actuate the original TG, and the felt pull would be realized accordingly. Right? Right? :mrgreen:

Agreed. Since the original TG is still utilized and the Shernic Bullpup just adds a linkage to actuate the original TG then a trigger job on the SKS TG would definitely affect the trigger feel on the Bullpup's trigger.